IMPROVEMENT OF CALIBRATION OF CONE-SHAPED ROLLS OF THE PIERCING MILL OF THE PIPE-ROLLING SHOP
https://doi.org/10.21122/1683-6065-2017-2-46-50
Abstract
The increase in operational durability of the technological tools of the piercing mill in the pipe-rolling shop and decrease in deficiency of produced pipes due to improvement of calibration of cone-shaped rolls is considered in the article. Increase in durability the piercing mandrels is evaluated as 1,3–4,3 times when using calibration of cone-shaped rolls with a smaller corner of an output cone. Improvement of quality of external surface of produced pipes was made due to application of experimental ring calibration of rolls. It is shown that this calibration demands big expenses of energy at the piercing.
About the Authors
V. S. Korovin
BSW - management company of "BMC" holding
Belarus
Zhlobin city, Gomel region, 37, Promyshlennaya str.
Belarus
Zhlobin city, Gomel region, 37, Promyshlennaya str.
A. N. Shashkov
BSW - management company of "BMC" holding
Belarus
Zhlobin city, Gomel region, 37, Promyshlennaya str.
Belarus
Zhlobin city, Gomel region, 37, Promyshlennaya str.
O. I. Kom
BSW - management company of "BMC" holding
Belarus
Zhlobin city, Gomel region, 37, Promyshlennaya str.
Belarus
Zhlobin city, Gomel region, 37, Promyshlennaya str.
A. G. Scheglov
BSW - management company of "BMC" holding
Belarus
Zhlobin city, Gomel region, 37, Promyshlennaya str.
Belarus
Zhlobin city, Gomel region, 37, Promyshlennaya str.
S. V. Avdeev
BSW - management company of "BMC" holding
Belarus
Zhlobin city, Gomel region, 37, Promyshlennaya str.
Belarus
Zhlobin city, Gomel region, 37, Promyshlennaya str.
Yu. L. Gerasimov
BSW - management company of "BMC" holding
Belarus
Belarus
Zhlobin city, Gomel region, 37, Promyshlennaya str.
Yu. L. Bobarikin
Pavel Sukhoi State Technical University of Gomel
Belarus
Gomel, 48, Oktyabrya ave.
Belarus
Gomel, 48, Oktyabrya ave.
References
1. Shevakin Ju. F., Glejberg A. Z. Proizvodstvo trub [Production of pipes]. Moscow, Metallurgija Publ., 1968, 440 p.
2. Vengura A. V., Avdeev S. V., Agafonov S. V., Kovalev V. N. Uvelichenie jekspluatacionnoj stojkosti tehnologicheskogo instrumenta proshivnogo stana truboprokatnogo ceha [The increase of service durability of the technological tool of piercing mill of the tube-rolling shop]. Lit’e i metallurgija = Foundry production and metallurgy, 2013, no. 4, pp. 94–98.
3. Potapov I. N., Poluhin P. I. Tehnologija vintovoj prokatki [Technology of screw rolling]. Moscow, Metallurgija Publ., 1990, 334 p.
4. Teterin P. K. Teorija poperechnoj i vintovoj prokatki [Theory of cross and screw rolling]. Moscow, Metallurgija Publ., 1983, 270 p.
5. Gerasimov Yu. L., Avdeev S. V., Bobarikin Yu. L. Sovershenstvovanie kalibrovki opravki diametrom 120 mm dlja proshivki zagotovok v dvuhvalkovom stane poperechno-vintovoj prokatki [Improvement of calibration of a mandrel with a diameter of 120 mm for an insertion of preparations in a two-roll camp of cross and screw rolling]. Metallurg = Metallurgist, 2015, no. 9, pp. 62–65.
6. Kovaleva I. A., Hodosovskaja N. A., Guzova I. A., Baban’kov P. V., Vengura A. V. Defekt «sledy ot nasechki na valkah» na naruzhnoj poverhnosti besshovnyh gorjachekatanyh trub [Defect «traces from cust on rollers» on the external surface of seamless hotrolled pipes]. Lit’e i metallurgija = Foundry production and metallurgy, 2012, no. 2, pp. 85–87.
7. http:// bypatents.com/3-u8926-valok-dlya-proshivnogo-stana-s-kolcevojj-kalibrovkojj.html.
8. Danilov F. A., Glejberg A. Z., Balakin V. G. Gorjachaja prokatka i pressovanie trub [Hot rolling and pressing of pipes]. Moscow, Metallurgija Publ., 1972, pp. 41–42.
Review
For citations:
Korovin V.S., Shashkov A.N., Kom O.I., Scheglov A.G., Avdeev S.V., Gerasimov Yu.L., Bobarikin Yu.L. IMPROVEMENT OF CALIBRATION OF CONE-SHAPED ROLLS OF THE PIERCING MILL OF THE PIPE-ROLLING SHOP. Litiyo i Metallurgiya (FOUNDRY PRODUCTION AND METALLURGY). 2017;(2):46-50. (In Russ.) https://doi.org/10.21122/1683-6065-2017-2-46-50
Views:
634
Email this article 