KINEMATICAL FEATURES OF FORMATION OF A FLANGE WITH MINIMUM TENSION OF A TRANSIENT TOROIDAL SURFACE
https://doi.org/10.21122/1683-6065-2018-1-132-136
Abstract
The technology of plastic forming of wide flanges in tube billets with the predicted length of the transitional toroidal section between the outer plane of the flange and the internal cavity of the pipe is proposed. The procedure for calculating the length of this section is given. In order to eliminate the toroidal portion in the flange formed during the flanging of the pipe, it is proposed to perform its plastic shaping by depositing the cylindrical part of the workpiece. Equations for calculating the extent of the free surface on the toroidal part of the workpiece when it is shaped, depending on the coefficient of contact friction and the presence of a radial support of the flange are obtained. The variant of forming in the flange the toroidal section in the stamp with the compensation cavity is proposed. Equations for calculating the deformation force and the extent of the free surface are given.
About the Author
M. I. Sidorenko
Belarusian National Technical University
Belarus
Minsk, Belarus, 65, Nezavisimosti ave.
Belarus
Minsk, Belarus, 65, Nezavisimosti ave.
References
1. Zubcov M. E. Listovaja shtampovka [Sheet stamping]. Leningrad, Mashinostroenie Publ., 1980, 432 p.
2. Popov E. A. Osnovy teorii listovoj shtampovki [Fundamentals of the theory of sheet punching]. Moscow, Mashinostroenie Publ., 1968, 248 p.
3. Romanovskij V. P. Spravochnik po holodnoj shtampovke [Cold stamping guide]. Leningrad, Mashinostroenie Publ., 1979, 520 p.
4. Isaevich L. A., Sidorenko M. I., Gurinovich V. A., Shimanskij A. V. Raschet usilija deformirovanija pri plasticheskom formoizmenenii otbortovannogo flanca v trubnoj zagotovke [Calculation of the deformation force during the plastic shaping of a flanged flange in a pipe blank]. Vestnik BNTU = Bulletin of BNTU, 2007, no. 3, pp. 10–15.
5. Gorbunov M. N. Tehnologija zagotovitel’no-shtampovochnyh rabot v proizvodstve samoletov [Technology of blanking and stamping works in the production of aircraft]. Moscow, Mashinostroenie Publ., 1981, 224 p.
6. Abibov A. L. Tehnologija samoletostroenija [Technology of aircraft construction]. Moscow, Mashinostroenie Publ., 1970, 508 p.
7. Kajushin V. A. e. a. Instrument dlja otbortovki koncov trub [Tool for flanging of pipe ends]. Patent USSR 897344, pp. 2.
8. Kajushin V. A. e. a. Press dlja otbortovki koncov trub [Press for flanging of pipe ends]. Patent USSR 614848, pp. 3.
9. Kajushin V. A. e. a. Instrument dlja otbortovki koncov trub [Tool for flanging of pipe ends]. Patent USSR 620313, pp. 2.
10. Kajushin V. A. e. a. Instrument dlja otbortovki koncov trub [Tool for flanging of pipe ends]. Patent USSR 770618, pp. 2.
11. Kajushin V. A. e. a. Ustrojstvo dlja otbortovki trub [Pipe Flaring Device]. Patent USSR 642049, pp. 3.
12. Kajushin V. A. e. a. Sposob poluchenija ploskih flancev [Method for producing flat flanges]. Patent USSR 889203, pp. 2.
13. Isaevich L. A., Gurinovich V. A., Sidorenko M. I., Shimanskij A. V. Raschet velichiny osadki pri plasticheskom formoobrazovanii flanca v trubnoj zagotovke [Calculation of the value of the draft during the plastic shaping of the flange in the pipe blank]. Respublikanskij mezhvedomstvennyj sbornik nauchnyh trudov «Mashinostroenie» = The Republican interdepartmental collection of scientific papers «Mechanical Engineering», 2007, no. 22, pp. 363–366.
14. Gurinovich V. A. Progressivnye metody obrabotki zagotovok i vosstanovlenija detalej [Progressive methods of processing blanks and restoring parts]. Minsk, BNTU Publ., 2007, 208 p.
15. Guringovich V. A., Isaevich L. A., Sidorenko M. I., Shimanskij A. V. Kinematika techenija metalla pri formoobrazovanii flanca v trubchatoj zagotovke s lokalizaciej ochaga deformacii [Kinematics of metal flow during the formation of a flange in a tubular blank with localization of the deformation center]. «Nauka – obrazovaniju, proizvodstvu, jekonomike» Materialy IV Mezhdunarodnoj nauchno-tehnicheskoj konferencii = «Science – Education, Production, Economics» Materials of the IV International Scientific and Technical Conference. Minsk, 2006, no. 1, pp. 193–197.
16. Isaevich L. A., Sidorenko M. I., Gurinovich V. A. Raschet usilija deformirovanija pri plasticheskom formoobrazovanii flanca v trubnoj zagotovke [Calculation of the deformation force during the plastic shaping of the fl in the pipe blank]. Lit’e i metallurgija = Foundry production and metallurgy, 2007, no. 1, pp. 140–145.
17. Gurinovich V. A. e. a. Ustrojstvo dlja formoobrazovanija flanca v trubnoj zagotovke [Device for forming a flange in a pipe blank]. Patent RB 4086, 2005, pp. 47.
18. Isaevich L. A., Guringovich V. A., Sidorenko M. I., Shimanskij A. V. Osobennosti formoobrazovanija perehodnoj zony v otbortovannom flance trubnoj zagotovki [Features of the formation of the transition zone in the flanged tube blank]. «Mashinostroenie i tehnosfera». Sbornik trudov XIV Mezhdunarodnoj nauchno-tehnicheskoj konferencii = «Mechanical engineering and technosphere». Proc. of the XIV International Scientific and Technical Conference. Sevastopol, 2007, no. 1, pp. 96–99.
19. Isaevich L. A., Shimanskij A. V., Guringovich V. A., Sidorenko M. I. Opredelenie tehnologicheskih parametrov processa formoobrazovanija flanca v trubnyh zagotovkah [Determination of technological parameters of the process of shaping the flange in tube billets]. «Sovremennye metody i tehnologii sozdanija i obrabotki materialov». Materialy III Mezhdunarodnoj nauchno-tehnicheskoj konferencii = «Modern methods and technologies for the creation and processing of materials». Materials of the III International Scientific and Technical Conference. Minsk, 2008, no. 3, pp. 117–122.
20. Stepanenko A. V. Prokatka polos peremennogo profilja [Rolling of strips of variable profile]. Gomel, IMMS NAS of Belarus Publ., 2001, 180 p.
21. Semenov E. I. Kovka i shtampovka: Spravochnik [Forging and stamping: Directory]. Moscow, Mashinostroenie Publ., 1985, no. 1, 568 p.
22. Grudev A. P. Vneshnee trenie pri prokatke [External friction during rolling]. Moscow, Metallurgiya Publ., 1973, 298 p.
23. Tret’jakov A. V. Mehanicheskie svojstva metallov i splavov pri obrabotke metallov: Spravochnik [Mechanical properties of metals and alloys in metal processing: Directory]. Moscow, Metallurgiya Publ., 1973, 224 p.
Review
For citations:
Sidorenko M.I. KINEMATICAL FEATURES OF FORMATION OF A FLANGE WITH MINIMUM TENSION OF A TRANSIENT TOROIDAL SURFACE. Litiyo i Metallurgiya (FOUNDRY PRODUCTION AND METALLURGY). 2018;(1):132-136. (In Russ.) https://doi.org/10.21122/1683-6065-2018-1-132-136
Views:
2096
Email this article 