Ventilation of molds for die casting
https://doi.org/10.21122/1683-6065-2019-1-34-37
Abstract
This paper describes the factors that affect gas content in castings during pressure molding. The possibility of removing air and gases from the cavity of the mold through the ventilation channels in the process of filling it with liquid metal is considered. It is shown that the previously used assumption about the outflow of gases from the mold as through a hole in a thin wall is not correct. The calculations, taking into account the friction factor in narrow ventilation ducts, showed that the required crosssectional area of the ventilation ducts increases 4–6 times with a depth of 0,12 mm. If the obtained value of the cross-sectional area of the ventilation ducts is not possible to realize, at a given depth, it is proposed to use an accompanying vacuum to solve the problem.
About the Authors
A. M. Mikhaltsov
Belarusian National Technical University
Belarus
Minsk, Belarus, 65, Nezavisimosti аve.
Belarus
Minsk, Belarus, 65, Nezavisimosti аve.
A. A. Pivovarchyk
Yanka Kupala State University of Grodno
Belarus
Grodno, Belarus, 22, Ozheshko str.
Belarus
Grodno, Belarus, 22, Ozheshko str.
References
1. Vejnik А. I. Teorija osobyh vidov lit’ja [Special Casting Theory]. Moscow, Mashgiz Publ, 1958, 300 p.
2. Mikhaltsov A. M. Tehnologija litejnoj formy: uchebn. posobie [Mold technology: textbook. allowance]. Minsk, BNTU Publ., 2011. 109 p.
3. Mihaltsov A. M., Pivovarchyk A. A., Subbota A. A. Gazotvornost’ razdelitel’nyh pokrytij dlja press-form lit’ja aljuminievyh splavov pod davleniem [Gas-creation of separating coverings for molds for diecasting of aluminum alloys]. Lit`e i metallurgiya Foundry production and metallurgy, 2010, no. 4, pp. 85–89.
4. Mihaltsov A. M., Pivovarchyk A. A. Jerozionnaja stojkost’ smazok pri izgotovlenii otlivok iz aljuminievyh splavov metodom lit’ja pod davleniem [Erosion resistance of lubrications at production of castings of aluminum alloys by means casting under pressure]. Lit`e i metallurgiya Foundry production and metallurgy, 2008, no. 2, pp. 47–51.
5. Mihaltsov A. M., Pivovarchyk A. A. Issledovanie adgezionnoj sposobnosti smazok na osnove kremnijorganicheskih polimerov dlja lit’ja pod davleniem aljuminievyh splavov [Investigation of the adhesiveness of lubricants based on organosilicon polymers for die casting of aluminum alloys]. Litejshhik Rossii Rossian Foundryman, 2007, no. 7, pp. 11–13.
6. Mikhaltsov A. M. Issledovanie i razrabotka sposobov snizhenija gazosoderzhanija i poristosti otlivok iz aljuminievyh splavov pri lit’e pod davleniem. Diss. kand. tehn. nauk [Research and development of methods for reducing gas content and porosity of aluminum alloy castings during injection molding. Cand. of тech. sci. diss.]. Minsk, 1985. 209 p.
7. Bahmat V. A. e. a. Ustrojstvo dlja vakuumirovanija press-form lit’ja pod davleniem [Device for vacuum mold injection molding]. Patent USSR no. 1574356.
Review
For citations:
Mikhaltsov A.M., Pivovarchyk A.A. Ventilation of molds for die casting. Litiyo i Metallurgiya (FOUNDRY PRODUCTION AND METALLURGY). 2019;(1):34-37. (In Russ.) https://doi.org/10.21122/1683-6065-2019-1-34-37
Views:
2628
Email this article 