Advanced materials used for development of lubricated compositions for die casting
https://doi.org/10.21122/1683-6065-2019-3-70-73
Abstract
The article presents the requirements for the lubricants used in die casting of non-ferrous alloys and polymer materials. The methodology for conducting research to determine the lubricating properties of materials, as well as the results of studies of the lubricating qualities of materials used in the development of lubricant compositions for die casting of non-ferrous alloys and polymer products are presented. It is shown that the use of the materials researched under study reduces the effort to extract the metal rod from the casting by 4.5–8.9 times. It has been established that it is advisable to use petroleum jelly and fus (by-product of vegetable oil) as materials used to develop the composition of a lubricant for die-casting non-ferrous alloys and polymer products. The lubricity of these materials is, on average, 28.8–51.2% higher than that of other lubricants studied.
About the Authors
A. M. Mikhaltsov
Belarusian National Technical University
Belarus
Minsk, 65, Nezavisimosti ave.
Belarus
Minsk, 65, Nezavisimosti ave.
A. A. Pivovarchyk
Yanka Kupala State University of Grodno
Belarus
Grodno City, 22, Ozheshko str.
Belarus
Grodno City, 22, Ozheshko str.
A. A. Skaskevich
Yanka Kupala State University of Grodno
Belarus
Grodno City, 22, Ozheshko str.
Belarus
Grodno City, 22, Ozheshko str.
References
1. Mikhaltzov A. M., Rozum V. A., Pivovarchyk A. A. Vodojemul’sionnye smazki dlja press-form lit’ja pod davleniem [Water emulsion lubricants for injection molding molds]. Lit’e i metallurgija = Foundry production and metallurgy, 2005, no. 4, pp. 104–106.
2. Pivovarchyk A. A., Mikhaltzov A. M. Smyvaemost’ razdelitel’nyh pokrytij pri izgotovlenii otlivok iz aljuminievyh splavov metodom lit’ja pod davleniem [Washability of separation coatings in the manufacture of castings from aluminum alloys by injection molding]. Lit`e i metallurgiya = Foundry production and metallurgy, 2018, no. 1, pp. 78–83.
3. Kalinchev E. L., Sakovtseva M. B. Jeffektivnoe lit’e pod davleniem polimernyh materialov so smazkami [Effective injection moulding of polymer materials with lubricants]. Polimernye materialy = Polymer materials, 2014, no 7, pp. 14–26.
4. Pivovarchyk E. V., Mikhaltsov M. A. Smazka dlja izgotovlenija peschano-smoljanyh sterzhnej po nagrevaemoj osnastke [Lubricants for the manufacture of sand-smoothed rods by hydraulic tooling]. Lit’e i metallurgija = Foundry production and metallurgy, 2018, no. 1, pp. 69–74.
5. Mikhaltzov A. M., Pivovarchyk A. A., Subbota A. A. Gazotvornost’ razdelitel’nyh pokrytij dlja press-form lit’ja aljuminievyh splavov pod davleniem [Gasification of separation coatings for die-casting molds of aluminum alloys under pressure]. Lit`e i metallurgiya = Foundry production and metallurgy, 2010, no. 4, pp. 85–89.
6. Mikhaltzov A. M., Pivovarchyk A. A., Rozum V. A. Razrabotka vodojemul’sionnyh smazok dlja press-form lit’ja pod davleniem [Development of water-based lubricants for injection molds]. Litejnoe proizvodstvo = Foundry production, 2006, no. 3, pp. 15–16.
7. Mikhaltzov A. M., Pivovarchyk A. A., Slepneva L. M. Razrabotka kompleksnogo komponenta na osnove kremnijorganicheskih polimerov dlja press-form lit’ja pod davleniem [Development of a complex component based on organosilicon polymers for injection molds]. Lit`e i metallurgiya = Foundry production and metallurgy, 2008, no. 1, pp. 129–133.
8. Pivovarchyk A. A., Slepneva L. M., Rozum V. A. Razrabotka razdelitel’nyh pokrytij na osnove kremnijorganicheskih materialov dlja press-form lit’ja pod davleniem [Development of separation coatings on the basis of organosilicon materials for die-casting molds]. Litejshhik Rossii = Russian foundrymen, 2007, no. 1, pp. 36–40.
9. Mikhaltzov A. M., Pivovarchyk A. A., Dyatlovsky S. K. Materialy razdelitel’nyh pokrytij press-form lit’ja aljuminievyh splavov pod davleniem [Materials of separation coatings of die-casting molds of aluminum alloys under pressure]. Litejshhik Rossii = Russian foundrymen, 2012, no. 7, pp.33–40.
10. Pivovarchyk A. A., Mihaltzov A. M. Formirovanie sloja razdelitel’nogo pokrytija na poverhnosti press-formy pri lit’e pod davleniem [Forming a layer of the separation coating on the surface of the mold during injection molding]. Lit`e i metallurgiya = Foundry production and metallurgy, 2015, no. 1, pp. 62–65.
11. Mikhaltsov А. М., Pivavarchyk A. A. Issledovanie adgezionnoj sposobnosti smazok na osnove kremnijorganicheskih polimerov dlja lit’ja pod davleniem aljuminievyh splavov [Study adhesiveness greases based on silicone polymers for injection molding of aluminum alloys]. Lit’e i metallurgija = Foundry production and metallurgy, 2007, no. 1, pp. 131–134.
12. Mikhaltzov A. M., Pivovarchyk A. A. Jerozionnaja stojkost’ smazok pri izgotovlenii otlivok iz aljuminievyh splavov metodom lit’ja pod davleniem [Erosion resistance of lubricants in the manufacture of castings from aluminum alloys by injection molding]. Lit`e i metallurgiya = Foundry production and metallurgy, 2008, no. 2, pp. 47–51.
13. Mikhaltzov A. M., Pivovarchyk A. A. Issledovanie adgezionnoj sposobnosti smazok na osnove kremnijorganicheskih polimerov dlja lit’ja pod davleniem aljuminievyh splavov [Investigation of the adhesiveness of lubricants based on organosilicon polymers for die casting of aluminum alloys]. Litejshhik Rossii = Foundry production, 2007, no. 7, pp.11–13.
14. Mikhaltzov A. M., Pivovarchyk A. A. Nakoplenie razdelitel’nyh pokrytij na rabochej poverhnosti tehnologicheskoj osnastki pri lit’e pod davleniem aljuminievyh splavov [Accumulation of separation coatings on the working surface of the tooling when casting aluminum alloys under pressure]. Metallurgiya: Respublicanskij mezhvedomstvennyi sbornik nauchnyh trudov = Metallurgy: Republican interdepartmental collection of scientific works, Minsk, BNTU Publ., 2007, vyp. 31, pp. 179–189.
Review
For citations:
Mikhaltsov A.M., Pivovarchyk A.A., Skaskevich A.A. Advanced materials used for development of lubricated compositions for die casting. Litiyo i Metallurgiya (FOUNDRY PRODUCTION AND METALLURGY). 2019;(3):70-73. (In Russ.) https://doi.org/10.21122/1683-6065-2019-3-70-73
Views:
570
Email this article 