The Strength Properties Of Adhesive Joints Used In The Creation Of Plastic Model Kits Evaluation
https://doi.org/10.21122/1683-6065-2022-4-115-122
Abstract
The article presents information on model plastics presented on the market of the Republic of Belarus. The analysis of methods for creating accurate model sets using both 3D printing from thread and granules, and obtaining model sets from an array of model plastic using 3D milling is carried out. The properties were evaluated and the behavior of glued and solid plastics under compressive loads in the longitudinal and transverse directions was shown. Economic efficiency assessment of various methods of obtaining model sets is given, based on a comparison of the cost of materials and the production process itself.
About the Authors
M. I. Kalinichenko
Belarusian National Technical University
Belarus
Minsk, Belarus, 65, Nezavisimosti ave.
Belarus
Minsk, Belarus, 65, Nezavisimosti ave.
B. M. Nemenenok
Belarusian National Technical University
Belarus
Minsk, Belarus, 65, Nezavisimosti ave.
Belarus
Minsk, Belarus, 65, Nezavisimosti ave.
References
1. Neljub I.A., Kushel’ P.A., Rovin S. L. Osobennosti i preimushhestva primenenija sovremennyh plastopolimernyh materialov dlja izgotovlenija model’noj osnastki [Features and benefits of using modern plastic polymer materials for the manufacture of pattern equipment]. Lit’e i metallurgija = Foundry production and metallurgy, 2010, no. 4, pp. 36–39.
2. Kalinichenko M. L. Sovremennye sposoby sozdanija model’nyh komplektov dlja lit’ja [Modern ways to create model kits for casting]. Lit’e i metallurgija = Foundry production and metallurgy, 2018, no. 3, pp. 125–130.
3. Rogov V.A., Poznjak G. G. Tehnologija mashinostroenija. Shtampovoe i litejnoe proizvodstvo [Engineering technology. Die and foundry production]. Moscow, Izdatel’stvo Jurajt Publ., 2019, 330 p.
4. Val’ter A. M., Protopopov A.A. Osnovy litejnogo proizvodstva [Foundry basics]. Moscow; Vologda, Infa‑Inzhenerija Publ., 2019, 332 p.
5. Kalinichenko M. L., Dolgij L. P., Kalinichenko V.A. Analiz sovremennyh kompozicionnyh materialov, primenjaemyh pri izgotovlenii model’nyh komplektov dlja melkoserijnogo litejnogo proizvodstva, poluchennyh s pomoshh’ju tehnologii skleivanija [Analysis of modern composite materials used in the manufacture of model kits for small‑scale foundry production, obtained using gluing technology]. Lit’e i metallurgija = Foundry production and metallurgy, 2020, no. 3, pp. 15–22.
6. Leushin I. O., Reshetov V.A., Romanov A. D., Bol’shakov A.A. Primenenie RP‑tehnologii dlja izgotovlenija malogabaritnoj osnastki v melkoserijnom proizvodstve lit’ja [The use of RP‑technology for the manufacture of small tooling in small‑scale production of casting]. Izvestija MGTU MAMI = Proceedings of MSTU MAMI, 2013, no. 2, pp. 229–232.
7. https://extxe.com/9761/additivnye-tehnologii-i-litejnoe-proizvodstvo/.
8. Zelenko M.A., Nagajcev M. V., Dovbysh M. V. Additivnye tehnologii v mashinostroenii [Additive technologies in mechanical engineering]. Moscow, NAMI Publ., 2015, 220 p.
9. https://extxe.com/3834/sushhnost-i-osobennosti-additivnyh-tehnologij/.
10. Kalinichenko M. L., Dolgij L. P., Kalinichenko V.A. Tehnologija skleivanija: teorija, praktika, materialy [Bonding technology: theory, practice, materials]. Minsk, BNTU Pub., 2021, 187 p.
Review
For citations:
Kalinichenko M.I., Nemenenok B.M. The Strength Properties Of Adhesive Joints Used In The Creation Of Plastic Model Kits Evaluation. Litiyo i Metallurgiya (FOUNDRY PRODUCTION AND METALLURGY). 2022;(4):115-122. (In Russ.) https://doi.org/10.21122/1683-6065-2022-4-115-122
Views:
244
Email this article 