Preview

Assessment of the unevenness of plastic deformation in drawing high-strength pearlite steel wire

https://doi.org/10.21122/1683-6065-2025-3-56-60

Abstract

Under the control of plastic properties, the reliability of a preliminary assessment of the unevenness of plastic deformation during repeated drawing of high‑strength wire was compared using the calculated geometric parameter of the wedge‑shaped zone and the experimentally determined metal lift at the entrance to the working cone of the drawing. The geometric parameter of the wedge‑shaped zone does not characterize the effect on the formation of plastic properties of increased strength, the ratio of compressive and tensile stresses in the deformation zone with a change in a single compression, and therefore cannot be used as an indicator of the unevenness of plastic deformation during repeated drawing of high‑strength wire made of pearlite steel. The rise of metal at the entrance to the deformation zone of the drawing tool, determined by drawing on split lugs, is highly sensitive to changes in the main technological parameters of the drawing process and meets the criterion of uneven plastic deformation. To increase the uniformity of deformation during repeated drawing of high‑strength wire, it is necessary to reduce single compressions and reduce the angle of the working cone of the drawing as the total degree of deformation increases, as well as to carry out deformation by drawing with counter‑tension and in the mode of hydrodynamic friction.

About the Author

V. P. Fetisov

Russian Federation

Orel



References

1. Perlin I. L., Ermanok M. Z. Teoriya volocheniya [The teory of drawing]. Moscow, Metallurgiya Publ., 1971, 448 p.

2. Fetisov V. P. Deformacionnoe starenie stali pri volochenii provoloki [Deformational aging of steel during wire drawing]. Minsk. Belorgstankinpromizdat Publ., 1996, 120 p.

3. Gridnev V. N., Gavriluk V. G., Meshkov Ju. Ja. Prochnost’ i plastichnost’ holodnodeformirovannoi stali [Stregth and ductility of cold-rolled steel]. Kiev, Naukova dumka Publ., 1974, 231 p.

4. Gubkin S. I. Plasticheskaya deformaciya metallov. T. 1. [Plasticdeformation of metals. Vol. 1]. Moscow, Metallurgizdat Publ., 1961, 376 p.

5. Backofen W. Processy deformacii [A deformation processing]. Moscow, Metallurgiya Publ., 1977, 288 p.

6. Avitzur B. Metal forming. Processes and analysis. New York, 1968, p.172.

7. Fetisov V. P. Kontrol’ plastichnosti vysokoprochnogo sostoyaniya holodnodeformirovannoj perlitnoj stali [Control of plasticity of high-strength condition of cold-formed pearlitic steel]. Lit’e i metallurgiya = Foundry production and metallurgy, 2024, no. 1, pp. 51–54.

8. Fetisov V. P. Plastichnost’ vysokoprochnoj provoloki [Ductility of high tensile wire]. Moscow, Intermet Inzhiniring Publ., 2011, 128 p.

9. Mamoru N., Takeshi K. Suppression of delamination in hypereutectoid steel wires by multi skin-pass drawing. Tetsu‑to‑hagane. J. ISIS, 2004, vol. 90, no. 8, pp. 588–592.

10. Fetisov V. P. Deformacionnoe uprochnenie uglerodistoj stali [Carbon steel strain hardening]. Moscow, Mir Publ., 2005, 200 p.


Review

For citations:


Fetisov V.P. Assessment of the unevenness of plastic deformation in drawing high-strength pearlite steel wire. Litiyo i Metallurgiya (FOUNDRY PRODUCTION AND METALLURGY). 2025;(3):56-60. (In Russ.) https://doi.org/10.21122/1683-6065-2025-3-56-60

Views: 23


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 1683-6065 (Print)
ISSN 2414-0406 (Online)